Osmo 3051 Polyx-Oil Raw Matte // *For Lighter Woods*
Osmo 3051 Polyx-Oil Raw Matte // *For Lighter Woods*
** Osmo 3051 - Raw/Matte (previously Osmo 3041 - Neutral) is designed to retain an untreated appearance on light colored woods such as Oak, Ash, Birch and Maple. It eliminates the permanent ‘wet-look’ that develops after the application of a clear oil-based finish and keeps the wood looking raw and untreated. It contains 2% white pigment to combat the amber look of natural oils. If used on a darker wood, the natural colors may appear muted. We like Osmo 3043 for darker woods.
This will leave a matte/raw sheen if used alone. If you would like a satin sheen, we recommend top coating in Osmo 3043 after drying. A single coat of 3051 will add a nice lightening effect, but if you’re going for more of a ‘whitewash’ you can apply a second coat, followed by the 3043. **
Our preferred finishing method and product, made from environmentally-friendly components for eco-conscious customers. Osmo Polyx Oil is derived from natural plant oils and waxes, providing a hard-wearing and protective surface that is resistant to common liquid spills. The oil is microporous and molecularly bonds with the wood, meaning it does not crack, flake, peel or blister. The finish maintains the natural look and feel of the wood, all while offering protection and durability.
ADVANTAGES:
One major advantage of a hardwax oil is that it’s much easier to repair/maintain vs a lacquer film finish, and in the event that minor signs of use occur the finish can maintained with supplied oils. With Osmo's Maintenance Oil its simple and quick to bring the finish "back to life".
ECO-FRIENDLY PRODUCT:
We are ever-committed to reducing the amount of VOC (Volatile Organic Compounds) we emit during our production process for environmentally conscious reasons, and are also trying to reduce the amount of toxins that our crew is exposed to for health safety precautions. Additionally, the hardwax-oil is a rub-on application (vs. other harsher methods such as spray-on which causes the finish to become airborne), and can be continuously DIY applied to refresh the wood on your table.
RECOMMENDATIONS:
To avoid minor signs of use, we recommend using coasters under serveware containing hot or cold liquids as well as cleaning up spills so as to not leave any moisture to set in over long periods that can cause spots or rings to occur to maintain the condition of the wood. However, spot-repairing is simple and quick if damages occur. Here is a link to a 5-minute maintenance/repair video for helpful tips when spot-repairing your wood furniture: https://vimeo.com/268291711
Cure Period: Osmo Hardwax-Oil(s) like all wood finishes have a cure period. We recommend allowing 2 weeks for the surface to fully cure and harden prior to normal use.
SHIPPING:
Upon checkout, please choose ‘OSMO PRODUCTS’. Free pickup is also available in South Lake Tahoe.
**Note, shipping rates may be higher depending on location (i.e. cross-country with multiple items).
PRODUCT DETAILS AND OVERVIEW:
Easy to apply – used by both professionals and homeowners
Extremely durable and hardwearing
Can be spot-repaired and refreshed with no sanding required
Microporous finish which does not crack, peel or flake
Very water and dirt resistant as well as juice, tea, cola, wine, beer, coffee.
Enhances the wood’s natural character
Saliva-resistant and sweatproof, suitable for children’s toys
APPLICATION:
Video tutorial here: https://www.youtube.com/watch?time_continue=1&v=40hjMvzg-90&feature=emb_logo
Always do a small test area before starting any project and follow the manufacturer’s instructions on the bottle at all times.
1. WITH A BRUSH OR ROLLER
First Coat: Apply one thin coat with a roller.
Stir the Polyx®-Oil well and prior to use
Brush or roll the product thinly and evenly onto the surface
Do not remove excess product, this will absorb into the wood surface over the drying period
Allow 8-10 hours drying time prior to proceeding to second coat
Second Coat: Roll or Brush a thin second coat
Brush or roll the second coat thinly and evenly onto the floor
Allow approximately 5-10 minutes for product to penetrate surface
Allow 8-10 hours drying time. Allow for good ventilation whilst drying.
Third Coat: Usually a third coat is not required, however highly absorbent or dry timbers may appear to require a third coat.
2. BY HAND WITH FLEECE APPLICATOR PADS
Apply two thin coats with our fleece applicator pads (best way to ensure you avoid over-application).
Stir the Polyx®-Oil well and pour into tray
Work the product into the wood thinly and evenly in figure 8 or circular motions using the fleece applicator pad
Be sure to thinly and evenly coat the surface and leave on the surface for approx. 5 minutes
Allow approx. 8-10 hours drying time. Allow for good ventilation whilst drying
Apply second coat following previous steps.
3. BY HAND WITH A CLOTH/RAG
Apply three thin coats with a lint-free microfibre cloth. ie. Osmo Easy Pads.
Stir the Polyx®-Oil well and prior to use
Work product into wood using cloth in a circular or figure 8 pattern
Allow roughly 15-minutes for oils to penetrate
Working with the grain, remove all excess product from surface
Allow 8-10 hours drying time prior to recoating
Apply second and third coats following previous steps
WARNING: Cloths saturated with product are a spontaneous combustion hazard and should be left out unfolded until dried, prior to disposal or preferably stored in a proper fireproof container
4. BY HAND WITH SCOTCHBRITE PADS
Apply two thin coats with non-abrasive white scotchbrite pads
Stir the Polyx®-Oil well and pour into tray
Work the product into the wood thinly and evenly in figure 8 or circular motions using a white pad
Be sure to thinly and evenly coat the surface and leave on the surface for approx. 5 minutes
With a clean white pad, polish the surface ensuring no swirl marks, rings, or wipe marks
Ensure all excess product is removed from surface
Allow approx. 8-10 hours drying time. Allow for good ventilation whilst drying
Apply second coat following previous steps.